This happened to a second tuner today. I replaced power supply (wall wart) and the tuner is now fully functional. This made me think it might be a good idea to add a B+/Vcc voltage item to the tuner menu in the firmware for troubleshooting I say this because, in addition to the network connection dr...

You can't have a series recording and a one-off recording of the same show. I understand that you haven't enabled that type of functionality. I'm sure that the code could be designed that would enable this. That is why I am pointing it out. To limit choices to either ALL or Series is inflexible.

The B button on the XBOX typically acts as a back button and if pressed enough times will back you completely out of the app. This does work fairly consistently through the HDHR app. But there are times where it doesn't and this really depends on the build. In the most current build (20190919f) in t...

Okay this is specific. Under Tasks a series has been set to record the Current Season, in the same place I see that there is an episode that will be rebroadcast from a previous season which I would like to record. Currently if I browse down to that item in the task list but there is no way for me to...

I've always thought they should go by ip address as that is something a user can control if they wish though it probably would need a line in the config file to use it as people have been told to expect ota over cable. This makes so much sense, I wish I had thought of it. Or they could assign throu...

I think what Neil means to say is that the sensitivity of the tuners can vary from one to another. I have serviced TV receivers for many years and RF tuners do require a certain amount of 'magic' to peak properly. There can be variance between identical models. Granted things are a lot better than t...

131F has stabilized and is no longer searching for a connection. What a chore this whole thing was. I still don't know it the tuner I subbed out is any good.

jasonl wrote: ↑

Tue Sep 17, 2019 3:28 pm

The RDC numbers are reasonable. The 1312 device isn't reporting any issues with the TA losing sync. 131F is. Bad TA.

1312 was losing sync that evening but seems to have stabilized. 131F is the box and TA that I replaced last week . K I'll get another.

It seems to only do this when the tuner isn't actively tuned to a channel. The log in Device ID: 131F6468 has actually rolled over.

** CORRECTED DEVICE ID I have turned the data back on here's the Device ID for the new tuner. Device ID: 131F6468 S/N: 37 dB Seconds: 15774 Corr Bytes: 0 Uncor Blks: 0 Errs Avg/Inst: 0 / 0 EQ Gain: 1.0 CURRENT RDC Freq: 10.000 MHz Power: 37 dBmV Delay: 695 uSec Retrans: 44 Device ID: 13129237 S/N: 3...

Darn You can change the tuner priority in WMC. That's if the tuner is paired with WMC. I recently replaced a Prime and the reason I needed to do this is so WMC and HDHRDVR didn't fight for the same tuner. I rarely had that problem before. Not in the mood right now to fight with resetting and reconf...

I checked the tuner log file and can see that both tuners are repeatedly doing this starting around 1pm on the card.. That is the same time that the tech was here..9am est. I called the cable company and they say as long as I have a picture then there is nothing that they can do. I asked them to sen...

Darn

Oh and I bypassed everything and ran a cable from the TA directly to the main cable input and the measurements did not improve.

Often I would agree with this but that same signal is feeding the prime which is giving a 13dBmV swing for the same frequency. Personally I don't like daisy chaining the prime through the TA, though usually on a cisco TA you can get away with such, I have seen issues with the internal amp of the TA...